PENGARUH PARAMETER PROSES 3D PRINTING TERHADAP KEKUATAN IMPAK MENGGUNAKAN METODE CHARPY PADA FILAMEN PLA
Keywords:
3D Printing, PLA filament, charpy impact testAbstract
The existence of 3D Printing technology in the manufacturing sector has brought big changes to the industrial world This research uses a 3D printing machine FDM model PRUSA area with dimensions of 220mm X 220mm X 250mm with a nozzle diameter of 0.4mm. The material used is a PLA filament with a diameter of 1.75mm with a variety of parameters, namely infill geometry (Grid, Lines, Triangles, Tri Hexagon, Cubic, Cubic Subdivision, Octet, Quarter Qubic, Concentric, Zig-Zag, Cross, Cross 3D and Gyroid), printing speed (40mm / s, 50mm / s and 60mm / s), flowrate (80%, 90% and 100%) and colling speed (40%, 50% and 60%) which are specified in ultimaker cura 4.7.1 so that produced 39 printed samples. The highest impact test results were found in the test specimen number 6 cubic subdivision of 0,00935 Joule/mm2 with a printing speed of 40, flowrate 80 and colling 40. The lowest impact test value in experiment number 24 cross is 0,00066 Joule/mm2 with a printing speed of 50, flowrate 90 and colling speed 50.
Downloads
References
Pristiansyah, Hasdinsah, & Sugiyarto. (2019). Optimasi Parameter Proses 3D Prinring FDM Terhadap Akurasi Dimensi Menggunakan Filamen Eflek. 11 (01).(Journal). Sungailiat : JURNAL TEKNOLOGI MANUFAKTUR, 2019 - : Vol. 11
septiawan, A. (2017). Pengarug parameter proses ektrusi 3D printer terhadap sifat mekanis cetak komponen berbahan filamen PLA.(Journal).teknik mesin 2017 –pp. 21-22.
Kurniadi, S. (2019). Pembuatan Alat Uji Impak Charpy Untuk Material Plastik Dengan Takik. 8 (1).
Wawandaru, M., & Fitri, M. (2017). Perancangan alat uji impak charpy untuk material plastik dengan takik.( Journal ),-Batam : Zona Mesin, 2017.-Vol.8.
Lubis, S., Djamil, S., & Yolanda. (2016). pengaruh orientasi objek pada proses 3D printing bahan polymer pla dan abs terhadap kekuatan tarik dan ketelitian dimensi.(Journal)// teknik mesin 2016,pp 27-36.
Suzen, Z. S., Hasdiansah, & Yuliyanto. (2020). Pengaruh tipe infill dan temperatur nozzle terhadap kekuatan tarik produk 3D printing filamen pla+ Esun. (Journal), sungailiat : Manutech : Jurnal Teknologi Manufaktur, 2020. – 2 :12
Trisnadi, W., Ismono, Fadelan, & Winardi, Y. (2017). Analisa Hasil Uji Impak Sampah Plastik Jenis PP, PET, dan Campuran (PP + PET).(Journal). Ponorogo : R.E.M (Rekayasa Energi Manufaktur), 2017.-1 : Vol.2
Doungkom P dan Jiamjiroch K (2019), Analysis of Printing Pattern and Infiltration Percent over the Tensile Properties of PLA Printed Parts by a Fuse Deposition Modelling Printer, Jurnal TSME-International Conference on Mechanical Engineering,- Pathumthan.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2021 Ongki Rio Irfany, Zaldy Sirwansyah Suzen, Ariyanto Ariyanto
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
