PERBANDINGAN ANALISIS ALIRAN PRODUK SPESIMEN UJI TARIK DAN UJI IMPAK MENGGUNAKAN SOFTWARE SOLIDWORK PLASTIC 2018 DAN AUTODESK INVENTOR 2020

Authors

  • Raski Irawan Politeknik manufaktur negeri Bangka Belitung
  • Evan Agusman
  • Muhammad Yunus
  • Idiar Idiar

Keywords:

Flow simulation, solidwork plastics, specimens

Abstract

The specimen is one of the tools intended for testing and research, both tensile and impact testing, in the mechanical laboratory of the Bangka Belitung State Manufacturing Polytechnic has plastic molds for making specimen products using injection molding machines but the use of these molds is not optimal due to the non-existent process parameters , solidwork plastic software is needed to simulate plastic flow and analyze the process parameters in the mold and then compare it with the inventor's software. In solving this problem using data collection methods, making 3D models, making flow designs and layouts, determining process parameters, making flow simulations with Solidwork Plastic software, making mold fill analysis with Inventor software and comparing simulation results so that the problem solving is focused. The optimal process parameters have been obtained, such as fill time 6.49 s, melt temperature 230°C, mold temperature 40°C, injection pressure limit 26.574 Mpa and clamp force 8.79 tonne on type A polypropylene(PP) material. schulman/polyfort FIPP MKF 4025 has minimal shrink mark defects, which are 0.07 mm. There is a significant comparison from the results of the analysis using solidwork plastic software and software inventor (mold fill analysis), including mass with an average of 4.53 grams and defects such as weld lines.

Downloads

Download data is not yet available.

References

Ali Khaerul Mufid, Cahyo Budiyantoro, Muhammad Budi Nur Rahman, (2017), “Perancangan Injection Molding Dengan Sistem Three Plate Mold Pada Produk Glove Box”, Jurnal Material dan Proses Manufaktur, vol. 1, no. 2, pp. 8-9

ASTM D 3641 – 02, Standart Practice for Injection Molding Test Speciments of Thermoplastic Molding and Extrusion Materials, ASTM International, USA.

ASTM D 955 – 00, Standart Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastic, ASTM International, USA.

Henry Permana, Topan, Syahrul Anwar, (2021), “ Produksi Proses Komponen Plastik Flip Flop Dengan Mesin Injeksi Molding Type Hidrolik”, Jurnal baut dan manufaktur, vol. 3, no. 2, pp 11-13

Heri Yanto, Ihsan Saputra, Sapto Wiranto Satoto, (2018), “Analisa Pengaruh Temperatur dan Tekanan injeksi molding Terhadap Cacat Produk”, Jurnal integrasi, vol. 10, no. 1, pp. 2-3

Suyadi, (2010), “Kaji Eksperimen Kekuatan Tarik Produk-Produk Berbahan Plastik Daur Ulang”, Prosiding Seminar Nasional Sains dan Teknologi”, Fakultas Teknik Universitas Wahid Hasyim, Semarang.

Umar Mahruf, Deni Shidqi K, (2020), “Analisis Aliran Fluida Polypropilena(PP) Dari Sampah Khusus Kemasan Mie Instan Pada Mesin Pelebur Plastik”, Jurnal Teknik Mesin, vol. 09, no. 2, pp. 3-4

U. Wahyudi, (2015), “Pengaruh Injection Time dan Backpressure Terhadap Cacat Penyusutan Pada Produk Kemasan Toples Dengan Injection Molding Menggunakan Material Polistyrene”, Jurnal Teknik Mesin, vol. 04, no. 3, pp. 6-7

Downloads

Published

20-07-2023

How to Cite

Irawan, R. ., Agusman, E. ., Yunus, M., & Idiar, I. (2023). PERBANDINGAN ANALISIS ALIRAN PRODUK SPESIMEN UJI TARIK DAN UJI IMPAK MENGGUNAKAN SOFTWARE SOLIDWORK PLASTIC 2018 DAN AUTODESK INVENTOR 2020. Prosiding Seminar Nasional Inovasi Teknologi Terapan, 3(01), 178–183. Retrieved from https://snitt.polman-babel.ac.id/index.php/snitt/article/view/421

Most read articles by the same author(s)

1 2 > >>