ANALISA PERBANDINGAN SIMULASI ALIRAN PLASTIK TUTUP GALON MENGGUNAKAN SOFTWARE SOLIDWORKS DAN INVENTOR

Authors

  • Arya Ramadhan Politeknik Manufaktur Negeri Bangka Belitung
  • Muhammad Nurfahrezy Politeknik Manufaktur Negeri Bangka Belitung
  • Muhammad Yunus
  • Idiar Idiar

Keywords:

Gallon cap, Mold fill analysis, Simulation, Solid works plastic

Abstract

A gallon lid is a closing tool whose main function is to keep the water from spilling and maintain the hygiene of the water in it to avoid dust and dirt from outside while providing user comfort in accessing and using water. In Bangka Belitung Province there is no factory that produces gallon lids even though the use of gallon lids is much needed for drinking water managers both small and medium. The purpose of making this final project is to produce optimal parameters from the simulation and get comparative results from simulations using Solid works plastic software with inventor Mold fill analysis software. In solving this problem using data collection methods, making 3D models of gallon lid Molds, determining alternative layout designs, making plastic flow simulations using software, and conducting comparative analysis. The optimal parameters obtained from the simulation results of the two software are, melt temperature 280 ° C, Mold temperature 60 ° C, fill time 0.4 s, injection pressure limits 200 MPa and clamp force limits 101.97 tonnes. For comparison of the simulation results of Solid works plastic with inventor Mold fill analysis layout 1 and 3 the difference in fill time on both is the same, which is 0.04 s, with ease off fill in Solid works marked with green and yellow indications while in inventor only identified green color and for defective weld lines on layout 1 and 3 in Solid works does not show any weld lines while in inventor there are weld lines on layout 1 and 3.

Downloads

Download data is not yet available.

References

Anwar, M. C., Budiyantoro, C., & Thoharudin. (2018). Optimalisasi Parameter Proses Injeksi Menggunakan Simulasi Moldflow untuk Meminimalkan Cycle Time dan Eliminasi Short Shot Pada Produk tempat. Jurnal Material dan Proses Manufaktur.

Bryce, M. D. (1998). Plastic Injection Molding Mold Design and Construction Fundamentals, Society of Manufacturing Engineers. Dearborn, Michigan.

Candra, S., Haryono, Yon, & Tenggara, A. (2009). Rancang Bangun Mould Dua Cavity Untuk Tutup Galon AIr Minum Isi Ulang.

Kavade, M. V., & Kadam, S. D. (2012). Parameter Optimization of Injection Molding of Polypropilene by using Taguchi Methodology.

Manual Plastics Technology Training Course KT1 Injection Moulding Materials, Injection Moulding Process. (2007).

Nicko, M. S., & Chalid, M. (2011). Karakteristik Material Regrind Komposit PP/Talcum Hasil Proses Hot Melt Mixing Material .

Permana, H., Topan, & Anwar, S. (2021). Produksi Proses Komponen Plastik Flip FLop Dengan Mesin Injeksi Molding Type Hidrolik. Jurnal Baut dan Manufaktur Vol. 03. No. 02.

Risaldi, & Hamaam, Z. G. (2022). DESAIN CETAKAN INJEKSI PLASTIK PRODUK TUTUP "GALON" AIR MINUM.

Sari, D. P., & Alamsyah, D. N. (2018). DESAIN MOLD PADA PLASTIC INJECTION MOLDING UNTUK PRODUK CASING PENGAMAN KENDARAAN (SEPEDA MOTOR) ATAS KASUS PENCURIAN.

Yulianto, I., Rispianda, & Prassetiyo, H. (2014). RANCANGAN DESAIN MOLD PRODUK KNOB REGULATOR KOMPOR GAS PADA PROSES INJECTION MOLDING. Jurnal Online Institut Teknologi Nasional.

Downloads

Published

20-07-2023

How to Cite

Ramadhan, A., Nurfahrezy, M., Yunus, M., & Idiar, I. (2023). ANALISA PERBANDINGAN SIMULASI ALIRAN PLASTIK TUTUP GALON MENGGUNAKAN SOFTWARE SOLIDWORKS DAN INVENTOR. Prosiding Seminar Nasional Inovasi Teknologi Terapan, 3(01), 120–126. Retrieved from https://snitt.polman-babel.ac.id/index.php/snitt/article/view/447

Most read articles by the same author(s)

1 2 > >>