RANCANG BANGUN PORTAL OTOMATIS MENGGUNAKAN PENGENALAN PLAT NOMOR MENGGUNAKAN CAMERA
Keywords:
Automatic Gate, Camera, Parking areaAbstract
Currently, every shopping center such as a mall must have good parking management, starting from recording incoming vehicles to recording exits based on certain rates charged to visitors. The increasing number of visitors coming to these parking areas will increase the busyness of parking operators. Therefore, a way is needed to help facilitate data collection of incoming and outgoing vehicles. Some devices used to facilitate parking data collection are by using computer devices, which have been widely applied for parking management both in shopping centers and offices. Data collection of vehicles entering and leaving the parking area, as well as calculations regarding the length of parking time and fees charged can be completed properly.
Downloads
References
A. Suryawinata and D. I. Saputra, “Perancangan dan Analisis Optical Character Recognition (OCR) Untuk Mencocokan Pelat Kendaraan Pada Data Base,” Telecommun. Networks, Electron. …, vol. 1, no. June, pp. 24– 36, 2021, [Online]. Available: https://ejournal.upi.edu/index.php/TELNECT/article/view/35878.
A. Santoso, D. Dj, D. Nurdiana, J. Ahmad, Y. No, and T. Rejo, “Rancang Bangun System Pintu Otomatis Menggunakan Keypad dan RFID Berbasis Arduino Mega 2560,” J. Ilm. Tek. Elektro, vol. 02, no. 1, pp. 5–13, 2021.
B. A. B. Ii, R. Pi, L. Komputer, E. Upton, and J. Lang, “Gambar 2.1 Raspberry PI [2],” pp. 4–19, 2014.
D. A. Irawati, “Pengembangan aplikasi pengenalan plat nomor kendaraan roda dua pada area parkir,” Semin. Nas. Sains dan Teknol. 2015, no. November, pp. 1–11, 2015.
H. Fattah, “Push Button,” LTETM Cellular Narrowband Internet of Things (NB-IoT). pp. 211–216, 2021, doi: 10.1201/9781003120018-23.
M. S. B. Utomo, “Prototype Sistem Buka Tutup Pintu Otomatis Pada Bendungan Untuk Mengatur Ketinggian Level Air Berbasis Arduino Uno,” thesis, Univ. Muria Kudus., 2018, [Online]. Available: http://eprints.umk.ac.id/9894/.
Muhammad Adib, Filsafat ilmu: onto-logi, epistemologi, aksiologi, dan logika ilmu pengetahuan. Yogyakarta: Pustaka Pelajar, 2011.
M. W. S. D. and Sulaiman, “Rancang Bangun Portal Parkir Otomatis Menggunakan Sidik Jari Berbasis Mikrokontroler,” Bina Darma Conf. Eng. Sci., vol. 2, no. 1, pp. 135–144, 2020.
R. Galih, “Sistem Kontrol Pengaturan Suhu Otomatis Pada Kandang Ayam Broiler Menggunakan Sensor DHT22 Berbasis Arduino Mega 2560 Dengan Menggunakan Esp-01 Sebagai Implementasi Dari Iot (Internet Of Things) Dengan Aplikasi Blynk,” Universitas Diponegoro, semarang, 2020.
R. Laganière, OpenCV 2 Computer Vision. Birmingham, B27 6PA, UK. Packt Publishing, 2011.
S. Yulida, A. Kusumawardhan, and H. Setijono, “Perancangan Sistem Pengenalan Plat Nomor Kendaraan Menggunakan Metode Principal Component Analysis,” J. Tek. POMITS, vol. 2, no. 1, pp. 177–182, 2013.
T. Tri Pamungkas, R. Rizal Isnanto, and A. Ajulian Zahra, “Pengenalan Plat Nomor Kendaraan Menggunakan Metode Template Matching Dan Jarak Canberra,” Transient, vol. 3, no. 2, pp. 166–173, 2014.
V. D. Wardana, “Rancang Bangun Alat Penyortir Benda Logam Dan Non Logam Sesuai Warna Menggunakan Sensor Proximity Dan Sensor Tcs 3200 Dengan Conveyor Berbasis Arduino Mega 2560,” 2020.
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Irgi Setiawan Ardhana, Muhammad Pikkri, Aan Febriansyah, Sirlus Andreanto Jasman Duli
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
