RANCANGAN & SIMULASI MICRO PUNCH UNTUK PEMBUATAN PELAT PENYAMBUNG TULANG RAHANG (MINI PLATE)
Keywords:
Micro punch, Mini plate, Product design and developmentAbstract
Bone joint plates have a high production potential. This can be seen from the number of cases related to trauma to the bone which has increased quite high in Indonesia. The jaw bone joint plate or commonly known as the mini plate serves to connect the bones in the jaw that has been traumatized or broken. The manufacture of mini plates generally uses an EDM machine, wire cutting and laser cutting which can only process with a gradual working principle. Based on the description above, it is necessary to manufacture a micro punch machine for the manufacture of jaw bone joint plates (mini plates), so that they can be used to mass produce mini plates. This study aims to design a mini punch machine for the manufacture of a mini plate using a research method that refers to the book Product Design and Development (Karl T. Ulrich, Steven D. Eppinger) in order to obtain an optimal machine design. The results obtained based on the research method used, obtained a micro punch machine design for the manufacture of a mini plate using the working principle of a progressive tool, a pneumatic prime mover and a material strip drive using a fedder system.
Downloads
References
Firdaus, Y. V., Jaelani, A. K., Herawati, F., & Yulia, R. (2021). Evaluasi penggunaan antibiotik profilaksis pada pasien bedah ortopedi di Rumah Sakit Bangil. Intisari Sains Medis, 12(2), 407-414.
Sho, A. S. (2022). Deskripsi Korban Mati Kecelakaan Lalu Lintas yang Dikirim ke RSUD Dr. Moewardi Tahun 2016-2020 (Berdasarkan Ciri-Ciri Luka).
Kurniawan, Y., Mahardika, M., Amrullah, M. H., & Cahyadi, B. (2022). Reducing the punch force in the circular punching process by preheating under the recrystallization temperature. Sinergi, 26(1), 31-36.
Amrullah, M. H. (2019). Studi Eksperimental Gaya Punch Dan Bentuk Sisi Potong Produk Pada Proses Punching Dari Lembaran Titanium (Doctoral dissertation, Universitas Gadjah Mada).
Y. Kurniawan, M. Mahardika, Suyitno, M. H. Amrullah. (2019). Effect of Preheating on Punch Force, Sheared Surface and Work Hardening in Cold Punching Process of Commercially Pure Titanium Sheet. International Review of Mechanical Engineering (I.RE.M.E.), Vol. 13, N. 9.
Nasution, A. Y. (2016). Pengujian Mesin Press Mekanik Semi Otomatis dengan Penggerak Motor Listrik 0.5 Hp. SINTEK JURNAL: Jurnal Ilmiah Teknik Mesin, 10(2).
Karl T. Ulrich, Steven D. Eppinger. (2012). Product Design and Development. McGraw-Hill.
Icon Facial Plating. Katalog Osteomod.
Presstool Component. Misumi Indonesia.
Compact Cylinder. Festo Indonesia.
Timah, P.M. (1996). Perancangan Die Set. Bangka, Bangka Belitung, Indonesia: POLMAN TIMAH
Timah, P.M. (1996). Perancangan Alat Pemotong. Bangka, Bangka Belitung, Indonesia: POLMAN TIMAH
Downloads
Published
How to Cite
Issue
Section
License
Copyright (c) 2022 Muhamad Hilal Khoidar, Yusuf Bahtiar Pradana, Muhammad Haritsah Amrullah, Sugianto
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
